Our fiberglass attic insulation work in North York is a top-up: blown fibreglass added over the insulation already on your attic floor, once the gaps in that floor are sealed. On an open attic floor, blown-in costs less than spray foam because loose-fill covers wide, open bays for a fraction of what foam would. This page is for you if you own a bungalow, semi or townhouse and the upstairs runs cold in winter or bakes in July.

When a top-up is enough

Old insulation that is dry and even but too thin stays where it is. It still works, there just isn't enough of it, so we blow new fibreglass straight over it until the attic floor is at full depth.

You can check this yourself from the attic hatch with a flashlight. You want a level layer across the bays, with no wet patches and no droppings. If that's what you see, a top-up is the right job. Any of these means the attic is short on insulation:

  • You can see the tops of the ceiling joists. When the wood pokes through, the layer is thinner than the joists are deep, and each bare joist lets heat straight up.
  • Your upstairs bakes in July. Sun on the shingles heats the attic, and a thin attic floor lets that heat down into the bedrooms. We cover why an upstairs bakes in July on its own page.
  • Snow melts off your roof in patches while the roofs next door stay white. That can mean heat is getting out through thin spots. It can also just be sun or a roof vent, so it's a hint, not proof.
  • The bedrooms under the attic stay colder in winter than the rooms downstairs, even with the furnace running.

Seal first, then blow

We air seal before any fibreglass goes on, because warm air leaking up from the house carries heat and moisture right through loose-fill. Fibreglass slows heat. It doesn't stop moving air. And once the new layer is down, the gaps under it are buried where nobody can get at them.

Our crew seals the openings in the attic floor: around the attic hatch frame, along the top plates where interior walls meet the ceiling, the holes drilled for wires and plumbing pipes, and the edges of ceiling light boxes. Each hole is small. Add them up over a winter and they let a lot of warm air into the attic.

Baffles go in at the eaves before we start blowing. A baffle is a stiff channel stapled between the rafters above each soffit vent. Outside air comes in at the soffit and moves up under the roof deck, and the baffle keeps that path clear once the deeper layer reaches the edge of the attic floor. Skip the baffles and the new insulation slumps into the eaves and blocks the soffit vents. A blocked attic holds moisture.

How much to add

Aim for R-60 in a North York fibreglass attic wherever there's room for it. SB-12, the energy efficiency part of the Ontario Building Code, sets a minimum nominal R-60 for a ceiling with attic space in a new Zone 1 house under compliance packages A1, A2, A4 and A6, and R-50 under packages A3 and A5.

North York is in Zone 1. SB-1 lists it at 3760 heating degree-days, below the 5000 that marks the Zone 1 cutoff.

Those numbers apply to new houses. For an older attic they're a target, and nothing requires you to bring it up to code. How high you can go depends on the room at the eaves and how deep the old layer already is. We measure what's there, work out how much the new layer has to add, and quote for that.

Townhouse and semi attics

Townhouse attic insulation and semi detached attic insulation get the same order of work, seal then blow, just in a smaller space. These attics are often low, with a tight hatch, sometimes in a closet ceiling. Our crew feeds the hose up through that opening.

In some townhouse rows and semis, your attic is open to the neighbour's side. Closing that gap is a fire-separation question for a qualified contractor or the City, so we don't touch it. We insulate your side, leave the opening alone, and show it to you so you can have it looked at.

Blown fibreglass works well up there because the hose reaches the far corners and low edges that nobody can crawl into.

When old insulation has to come out first

Old insulation has to come out first when it's wet, flattened or chewed up by rodents. Wet insulation holds water against your ceiling drywall and the framing. Flattened insulation has lost the air pockets that did the insulating. And nests and droppings shouldn't be buried under a new layer.

Our crew bags the old material, vacuums the attic floor, then seals and insulates the same way as above. The insulation removal page goes through that job in detail. Finding and closing the spots where animals got in is a job for a pest-control company, and we leave it to them.

Vermiculite is another matter. It looks like light, pebbly granules, grey-brown or gold, and Health Canada advises some of it may contain asbestos. If we find it in your attic, we stop and leave it undisturbed. Have a qualified lab or an abatement firm test it before anyone does more work up there.

Fiberglass or cellulose for the attic

Either one makes a good attic floor, and both blow in through the same hose. Fibreglass is spun glass fibre. It's light, it doesn't soak up water, and it's the simple pick for topping up a layer that's already there.

Cellulose is made from shredded paper. It's heavier and packs tight, which is why it's also used to fill closed wall cavities. If you want the walls done on the same visit as the attic, cellulose lets one material handle both. The cellulose insulation page explains how we fill walls.

Spray foam is the wrong choice for an open attic floor. It costs far more to cover the same area, and it belongs in tight, leaky spots like a rim joist. Whichever loose-fill you pick, sealing and baffles come first on every attic First Choice Insulation North York works on.

More on Attic Insulation

FAQ

Common questions about attic insulation

No, not if the old insulation is dry, even and free of droppings. Then it stays, and the new layer goes on top. Pull it out first if it's wet, flattened or damaged by rodents. If it turns out to be vermiculite, we leave it alone, and you should have a qualified lab or abatement firm test it before any work goes ahead.

Yes, as long as the old layer is dry and in good shape. We seal the gaps in the attic floor first and put baffles in at the eaves so the extra depth doesn't block the soffit vents. Fibreglass sits fine over old batts, old loose-fill or old cellulose.

It needs one if you can see the tops of the ceiling joists through the insulation. An upstairs that overheats in summer or stays cold in winter is another sign, and so is snow melting off your roof in patches before the roofs nearby. Usually a look from the attic hatch with a flashlight tells you enough.

No. On an open attic floor, blown fibreglass does the job for less money. Spray foam is worth its cost in tight, leaky spots like a rim joist or a crawl space, where loose-fill won't stay put. For an open attic, we seal the gaps and blow fibreglass over them.

Get a quote

Get a spray foam or insulation quote in North York

Call (437) 563-1415 or send the form. Tell us which room is cold, drafty or hot. We will come look at the spot behind it and give you a straight written quote.

Call Text Quote