Cellulose Insulation in North York, ON
We dense-pack cellulose into closed walls through small plugged holes, and we blow it over attic floors in homes in North York and nearby.

Cellulose insulation is what we blow into closed walls in North York homes, and onto attic floors that have gone thin. Our crew drills a small hole into each stud bay, packs the cellulose in tight through a fill tube and plugs the hole. Nobody tears a wall open. It suits bungalows, semis and townhouses with an outside wall that feels cold or an attic floor that needs a fresh layer.
Filling closed walls without opening them
A bedroom that stays cold with the heat running usually has an empty or half-empty exterior wall behind the drywall. Blown in wall insulation fills that wall cavity through a few small holes, so the wall stays closed. Each space between two studs is its own bay, and each bay gets its own hole. We drill from outside through the siding or from inside through the plaster or drywall. Which side depends on the wall finish and where you would rather see the patches.
We use the dense pack method. A long fill tube goes into the hole and runs up or down the bay, and the machine blows cellulose in until the bay won't take any more. At that density the material packs around wires, pipes and outlet boxes and has no empty space to slump into. Blow a wall loosely and you can end up with a gap at the top of the bay. Cold air finds it.
When a bay is full, a plug goes into the drill hole. Before anyone picks up a drill, we agree with you on where the holes go, what the plugs are and how the wall will look when we leave. We don't paint, repair siding or finish over the plugs. If a wall is going to need any of that, we tell you before we start so you can line up the right trade.
Which walls can be filled
The simple case is an empty cavity with nothing across it: one hole per bay, and the tube reaches the full height. Older houses are rarely that tidy. Plenty have fire blocking, a short horizontal piece of wood nailed between the studs partway up, or diagonal bracing. Either one splits the bay in two. The space above it needs its own hole, so the job needs more holes.
Old insulation already in the wall limits what fits. Batts that have sagged to the bottom of the bay leave open space above them, but a fill tube going in through a small hole can't pack properly around them. Every cellulose job we quote starts with a look inside the wall, through an outlet box, a small inspection hole or down from the attic along the top plate. When a wall won't take a proper fill, we say so and leave it alone.
Some older homes have vermiculite, a loose, pebbly fill that looks grey-brown or gold, poured into the attic or down the wall cavities. If our crew comes across it, we stop work at that spot and leave the material exactly as it is. We'll recommend having a qualified lab or abatement firm test it before any insulation work goes ahead there.
Cellulose or fibreglass loose-fill
Choosing cellulose for insulation means picking between two loose-fill materials that both go in through a hose. The difference is the spot each one suits.
- Both blow in. Each one is fed into a machine outside the house and carried through a hose to the attic floor or the wall.
- Cellulose is the denser of the two. It packs hard into a closed stud bay and stays put, so we use it for walls.
- Fibreglass loose-fill is lighter. It spreads easily over an open attic floor and adds little weight to the ceiling below, which makes it a good fit for a plain attic top-up.
- Both need to stay dry. Either kind clumps when wet and stops insulating. If we see a roof leak or signs of condensation, we point it out, and it has to be fixed before anything gets blown in.
- Neither one stops air by itself. Gaps leaking warm air into the attic need air sealing before any loose-fill goes over them.
Cellulose on the attic floor
Blown in cellulose works well on an attic floor once the air sealing is done. Warm air escapes upward through gaps around ceiling light boxes, plumbing stacks, the attic hatch and the top plates of interior walls, so we close those first. Then the cellulose goes down in an even layer between and over the joists, right out to the edges where the roof meets the walls.
Sometimes we'd pick fibreglass for the attic instead. One case is an old plaster ceiling, because we'd rather not load it with a denser material. The other is dry fibreglass that's still in good shape, where topping up with more of the same is the simpler job. Our attic insulation page covers the rest of the attic work, from clearing out old material to topping up a thin floor.
What you'll notice on the day
The insulation machine sits in the driveway, with a hose running from it to the wall or up into the attic. On a wall job you'll see a neat row of drill holes along the wall, one per stud bay. Where fire blocking splits the bays, there's a second row higher up.
Inside, we cover the floors and furniture near the work and keep the dust to that area. Cellulose is fine and dusty going in, so it helps to keep the doors to other rooms shut. Once the bays are full, the plugs go in and we clean up where we worked.
Before we leave, we walk the wall or the attic with you. You'll see where each hole was, where the plugs sit, and anything we noticed that needs another trade, like a loose piece of siding or a stain on the roof boards. The rest of the insulation work we do is on our main page.
FAQ
Common questions about cellulose (blown-in) insulation
Yes, we can blow insulation into existing closed walls as long as the cavities are empty or close to it. Our crew drills a hole into each stud bay, dense-packs cellulose through a fill tube and plugs the hole. A wall with old batts, a lot of blocking or vermiculite in it may not be suitable, so we check before we quote.
Dense pack cellulose is worth it when your exterior walls are empty, the rooms behind them feel cold, and you don't want the walls opened up. It fills a closed cavity through small holes, so there's no new drywall. In a wall that already has insulation in good condition it isn't worth doing, and we'll tell you if yours is one of those.
Cellulose packed at dense-pack density has very little room to settle in a closed wall, because each bay is blown until it can't take any more. Loosely blown cellulose can slump and leave an empty strip at the top of the bay, which is why we pack every bay tight. On an open attic floor, loose-fill does settle a little over time, so we blow the layer slightly deeper to allow for it.
No, cellulose should only go into a dry wall or attic. Wet cellulose clumps, stops insulating and holds moisture against the wood around it. If we find a leak, wet sheathing or signs of mould, we point it out and wait until it's fixed and dried out.
Get a quote
Get a spray foam or insulation quote in North York
Call (437) 563-1415 or send the form. Tell us which room is cold, drafty or hot. We will come look at the spot behind it and give you a straight written quote.